A&D FX-120i Scale & V4 AutoTrickler Combo

R 26,585.00

A&D FX-120i Scale & V4 AutoTrickler Combo

A&D FX-120i Scale & V4 AutoTrickler Combo

R 26,585.00

Note - No Calibration Weight Included (FX-i can be re-calibrated with 50gram / 100gram external weight)
Customers buying this FX-120i along with the Autotrickler will have preference, stock levels will determine this from time to time.

High-speed weighing with 1-second stabilization
Compact footprint: 198 mm × 294 mm (smaller than an A4 sheet of paper)
Protection mechanism against vertical and transverse overloading
Multiple weighing units: g, oz, lb, lb-oz, ozt, ct, mom, dwt, grain.
Large bright vacuum fluorescent display
GLP/GMP/GCP/ISO compliant output
Counting mode with the Automatic Counting Accuracy Improvement (ACAI) function
Percent mode function
Animal weighing (hold) function
Statistical calculation function
Comparator function with buzzer
Auto power on/off function
Underhook function

Specifications

Model	FZ-120i FX-120i	FZ-200i FX-200i	FZ-300i FX-300i	FZ-500i FX-500i
Capacity	122 g	220 g	320 g	520 g
Readability	0.001 g
Repeatability (standard deviation)	0.001 g
Minimum weight* (typical)	1.4 g
Linearity	±0.002 g
Stabilization time (when set to FAST under a good environment)	Approx. 1 second
Weighing pan size (diameter)	130 mm
External dimensions	193 (W) × 262.5 (D) × 85.5 (H) mm
Net weight	FZ-i Approx. 3.0 kg / FX-i Approx. 2.5 kg

* Pursuant to the USP

Since the original AutoTrickler was invented in 2016, it has become the go-to solution for long range shooters who need to measure accurate powder charges quickly.

While the core concept of precisely dispensing onto a lab quality balance has never changed, the mechanical design has constantly improved with two versions of the AutoThrow, Bluetooth support, any many part revisions as a result of new ideas, new processes, and user feedback.

AutoTrickler V4 is a clean slate redesign. Starting with the idea of a single assembly without needing manual adjustments, we looked at every part, every feature, every detail, and built exactly what the AutoTrickler should be.

Works with fine ball powders like CFE223 and H335
Works with large kernel powders like N570 and H50BMG
Maximum flow rate ~50 GN/s for large caliber rifle
Integrated electronics and motors with fixed cabling
Acrylic panel and silicone pads ensure assembly is stable, quiet, and level
All commonly replaced wear parts from previous versions no longer exist
Potential for performance improvements through app updates
Integrates with standard A&D FX or FZ 120i, 200i, 300i, or 500i

Inspired by an auger (and refined through simulation, testing, and iteration), a large tube with deep spiral grooves pours bulk powder at rates up to 50 GN/s, ramping down smoothly to within 1-2 grains of the target.

A smaller tube then takes over to complete the charge within a kernel using an efficient ramping curve that takes calibrated flow rates into account. By popular request, a green light shines down through the clear panel indicating the correct charge weight has been reached. Both tubes are driven directly by toothed timing belts which will not wear out over time.

The AutoTrickler rests on a clear acrylic panel with soft silicone pads that minimize vibration and noise. The housing can be easily lifted from the panel without disturbing the scale. Silicone pads added to the scale platform keep the entire assembly stable and level. A tilt adjustment within the housing will be factory set. Leveling the scale using its built-in bubble level will set the AutoTrickler at the correct tilt angle.

A speed setting within the Bluetooth app will allow a tradeoff between speed and precision based on user preference. Firmware configurability through the app will allow performance options to improve through software updates in the future.

The electronics module fits inside the housing and is replaceable if necessary. The motors are integrated so their short cables will never move or break. One cable connects the AutoTrickler to the FX-120i scale with 20 AWG wiring. Both ends are protected with strain relief and an in-line connector allows easy disconnection. The scale side of the cable can also be replaced separately from the rest of the electronics if needed.

The hopper incorporates a rotating valve so it can be removed easily. The hopper has a flat bottom so it can rest on a table while holding powder.

When in use, the hopper is positively locked into the housing. The hopper also blocks the powder reservoir from opening while the valve is open, so the potential for a spill is low.

To empty powder, first turn and remove the hopper. Then slide up the window and pour the powder into the hopper. Tilt the unit backwards to clear powder out of the tubes. Any remaining powder will be clearly visible either in the rear reservoir or by looking through the tubes.